If a new component would be installed, there are procedures for that which you need to bear in mind. The procedures have to be followed to install Profile Design Cobra bars properly. That is also a requirement on the policy for the warranty that is provided when you buy one. When you are now knowledgeable on such task, go to its dealer near the area.
You would be provided with a manual that indicates the procedures you must follow. If you prefer to get it done yourself, the tools that will be utilized on that must be prepared. An Allen or a torque wrench should be prepared. You will be needing a sandpaper since that will be utilized in making the parts smooth. When you got all of those tools, you may begin on this.
You have to avoid putting grease on its clamping area. When you will grease that, it will be causing that bar to slide from its place. You should be certain that a situation like that will not be happening specifically when you would use the bike. You will surely lose control as you would ride your bike. When it will be happening, it would be risky for you.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You should slide the lever to the bar. If it makes you uncomfortable, you should adjust it depending on what you want. You have to place it carefully. You have to remember that if it would be broken, it would affect the warranty of the material.
You could wrap it if you want to. If you would try it, you have to make sure that you are wearing your helmet. Check if it would be working properly before you would be using it on far away places.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
You would be provided with a manual that indicates the procedures you must follow. If you prefer to get it done yourself, the tools that will be utilized on that must be prepared. An Allen or a torque wrench should be prepared. You will be needing a sandpaper since that will be utilized in making the parts smooth. When you got all of those tools, you may begin on this.
You have to avoid putting grease on its clamping area. When you will grease that, it will be causing that bar to slide from its place. You should be certain that a situation like that will not be happening specifically when you would use the bike. You will surely lose control as you would ride your bike. When it will be happening, it would be risky for you.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You should slide the lever to the bar. If it makes you uncomfortable, you should adjust it depending on what you want. You have to place it carefully. You have to remember that if it would be broken, it would affect the warranty of the material.
You could wrap it if you want to. If you would try it, you have to make sure that you are wearing your helmet. Check if it would be working properly before you would be using it on far away places.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
About the Author:
When you are looking for information about Profile Design Cobra Bars go to the web pages online here today. You can see details at http://www.sportfactoryproshop.com now.
No comments:
Post a Comment